mirror of
https://expo.survex.com/repositories/expoweb/.git/
synced 2024-12-18 14:32:23 +00:00
97 lines
5.0 KiB
HTML
97 lines
5.0 KiB
HTML
<html>
|
|
<head>
|
|
<meta http-equiv="Content-Type" content="text/html; charset=utf8" />
|
|
<title>CUCC Expo Rigging Handbook: Artificial belays - bolts</title>
|
|
<link rel="stylesheet" type="text/css" href="/css/main2.css" />
|
|
</head>
|
|
<body>
|
|
<h2 id="tophead"> CUCC Expo Rigging Handbook</h2>
|
|
<h1>Bolt belays - choosing a location</h1>
|
|
|
|
<p>Deciding where to put the bolts for a new pitch is something of a black art,
|
|
which can be acquired only through much practice and wide experience of SRT in
|
|
general. This guide cannot substitute for experience underground.
|
|
<!--Particularly as the author has only ever bolted three pitches.
|
|
--></p>
|
|
|
|
<p>Inasmuch as there can be such a thing as a "typical" pitch, the "typical"
|
|
rig might be something like this. Start off a traverse line somewhere nice and
|
|
far back; often this gives you enough choice of location that you can use a
|
|
natural. Approach the pitch-head carefully, gardening as much loose material as
|
|
you can before there are cavers or ropes below for it to hit. Look for
|
|
somewhere good to place a Y-hang; if the pitch is awkward, this may have to
|
|
become a tri-hang - a very typical Expo pitch-head technique is a Y-hang
|
|
followed immediately by a deviation, to give full three-dimensional control
|
|
over the position of the hang. (Showoffs can achieve the same effect with a
|
|
triple bowline, if they know how to tie one.)</p>
|
|
|
|
<p>Having got the pitch-head bolts in, descend carefully, looking out below you
|
|
for any potential rub points, and looking around for good places to rebelay or
|
|
deviate. Remember that a deviation to avoid a rub point is only any use if it's
|
|
some way above the rub; don't just ab down until it starts rubbing and then
|
|
start looking for a rebelay or deviation.</p>
|
|
|
|
<p>Placing mid-pitch bolts is often a challenging business requiring you to
|
|
dangle on miniscule ledges or wedged against the walls while you drill. Don't
|
|
overdo it; if it's difficult to put the bolt in, it'll be difficult to rig off
|
|
in future. Many seasoned riggers swear by skyhooks as a means of positioning
|
|
yourself while you bolt, but don't rely on everyone else who uses the bolt
|
|
owning a set! Another trick is to use a borderline natural, which you wouldn't
|
|
trust to rig off, to support yourself while you drill.</p>
|
|
|
|
<p>Some caveats:</p>
|
|
|
|
<ul class="spacedout">
|
|
|
|
<li> Watch out for poor rock quality. In most cases the choice of anchor
|
|
placements is a compromise between the requirements of the hang and the
|
|
necessity of putting your spits into decent rock. Cracks are obviously to be
|
|
avoided; mineral veins are also apparently bad, but often there are so many of
|
|
these there's no way you can avoid them. Once you've settled on a
|
|
likely-looking location, get your hammer out and give the rock a few taps with
|
|
the pointy end. It should give a convincing high ringing noise, not a hollow
|
|
thud. (The difference in sound is much accentuated by a hammer with a metal
|
|
shaft, such as the Petzl bolting hammers, which are expensive but very good;
|
|
the club's cheap fibreglass-shafted hammers are rather more difficult in this
|
|
respect.)</li>
|
|
|
|
<li>If your chosen location is in a large block of rock which is well held
|
|
together but not well attached to the wall, it can look and sound fine, but
|
|
hold a nasty surprise in store. I was once about to start drilling in a
|
|
promising-looking location, marred only by a crack in the rock at least 20cm
|
|
away from where I wanted to bolt. Some suspicion made me stick the point of my
|
|
hammer in the crack and lever on it, at which point a plate of rock about a
|
|
metre across and half a metre thick slid off the wall and down the pitch,
|
|
taking my proposed spit location with it! Be alert for this sort of thing.</li>
|
|
|
|
<li>Bear in mind how difficult the rig will be for the user. In most cases, if
|
|
it's difficult to rig it'll be difficult to pass and vice versa, but watch out
|
|
for subtle gotchas like putting your Y-hangs too low down; this can make the
|
|
pitch impossible to get off! Don't force yourself and your companions into
|
|
dangerous manouvres like prusiking up one arm of the Y-hang.</li>
|
|
|
|
<li>When considering how the rope will hang from a particular location, don't
|
|
forget to take into account the length of the hanger and maillon. It almost
|
|
always needs to be higher up than you expect.</li>
|
|
|
|
<li>Spits are very much stronger when loaded perpendicular to their axis; so it
|
|
is usually best to place spits horizontally into the wall, which is usually the
|
|
easiest method anyway. Bear in mind the safe loading angles for the different
|
|
types of hanger - only rings, clowns and bollards can take a straight outward
|
|
pull. Bends are good for Y-hangs, where the pull is at an angle away from the
|
|
wall; twists are best left for straight downward pulls.</li>
|
|
</ul>
|
|
|
|
|
|
|
|
|
|
<hr />
|
|
See the <a href="drillbolts.html">Bolting </a> - Hang Fix anchoring<br />
|
|
See the <a href="/expofiles/documents/anchors/hangfixtraining.pdf">instructions and training</a>
|
|
- for expo bolting<br />
|
|
See the <a href="/expofiles/documents/anchors/anchor-appraisal-martingreen2020.pdf">2020 appraisal of anchors</a>
|
|
- comparison of alternatives <br />
|
|
See the <a href="rigit.html">Rigging and Bolting</a> - handbook
|
|
<hr /></body>
|
|
</html>
|