mirror of
https://expo.survex.com/repositories/expoweb/.git/
synced 2024-11-30 05:41:56 +00:00
119 lines
5.3 KiB
HTML
119 lines
5.3 KiB
HTML
<html>
|
|
<head>
|
|
<title>CUCC Expo Surveying Handbook: Hints & tips</title>
|
|
<link rel="stylesheet" type="text/css" href="../../css/main2.css" />
|
|
</head>
|
|
<body>
|
|
|
|
<h2 id="tophead">CUCC Expo Surveying Handbook</h2>
|
|
<h1>Wookey's hints and tips</h1>
|
|
|
|
<p>... to save you going back to do it again.</p>
|
|
|
|
<p><i>"hmm - not going to finish this even slightly, so some points to bear
|
|
in mind:"</i></p>
|
|
|
|
<ul>
|
|
<li>Take care with lights, batteries, helmets and anything else which could
|
|
be magnetic - check your gear on the surface, or your work could be seriously
|
|
impaired. If your light affects the compass, then hold it away from the
|
|
instrument when lighting it. Keep the compass well away from steel objects
|
|
like bolts, steel karabiners or maillons, tripods or ammo cans when sighting.</li>
|
|
|
|
<li>Write decimal points as slashes to stop them getting lost in the mud.
|
|
Make sure they don't look like "1"s. It is helpful to always write compass
|
|
readings as three digits before the decimal point, and clino as two digits
|
|
with a sign. Add leading zeroes if needed (eg. 031/5 +02/5).</li>
|
|
|
|
<li>"Notes" should call back readings to "Instruments" to check. Make sure
|
|
you call out what you have written, not what you heard. It helps to ensure
|
|
both of you have brains in gear if you change the format. Eg. "Instruments"
|
|
calls out "Compass thirty seven point five", and "Notes" calls back "Oh,
|
|
three, seven point five, compass".</li>
|
|
|
|
<li>Instead of writing all the data on one sheet, and the sketches on
|
|
another, you may like to write all the info for a few legs on the same sheet
|
|
so that mud does not accumulate on one important data sheet in grubby areas.</li>
|
|
|
|
<li>Have a separate front sheet without anything important on otherwise it
|
|
might get rubbed off.</li>
|
|
|
|
<li>Take at least one spare pencil!</li>
|
|
|
|
<li>Draw plans and extended elevations in horizontal bits of cave, with
|
|
cross sections for each typical section of passage. Orientate your cross
|
|
sections (ie. show which direction they are looking) on the plans. It helps
|
|
always to do the cross sections looking in a consistent direction.</li>
|
|
|
|
<li>Draw extended sections in two directions for vertical cave, with plans
|
|
where required. Mark directions on plans and sections otherwise they are
|
|
impossible to orientate later. A plan with only one station and no direction
|
|
indicator cannot be orientated. It is easiest if the drawer takes a spare
|
|
compass for this (doesn't have to be a good one) in vertical work.</li>
|
|
|
|
<li>Record the serial numbers of instruments (comp/clino/tape). Also write
|
|
down dates, endpoints, surveyors, cave, any conventions used for symbols,
|
|
passage widths etc.</li>
|
|
|
|
<li>Find out where you are going to join your survey to <b>before</b> you go,
|
|
otherwise your surveys will be left hanging in space. From 1996, the QM
|
|
list is supposed to tell you the nearest existing survey station - make
|
|
sure that you can identify this (look at the relevant year's survey book).</li>
|
|
|
|
</ul>
|
|
|
|
<h3>If using analogue instruments (i.e. Suunto)</h3>
|
|
<ul>
|
|
<li>The compass must be held level to get a meaningful reading. A left/right
|
|
tilt will cause a systematic over or under reading, whilst sighting up or
|
|
down a steep leg may cause the compass to stick. It is easier to sight from
|
|
the lower station by keeping the tape in position and sighting along it.</li>
|
|
|
|
<li>Practice using the compass above ground to avoid classic errors like
|
|
reading 56 as 64 (ie. counting the wrong way from the 60 marker).</li>
|
|
|
|
<li>Degrees are on the <b>left hand</b> scale on clinos. The other scale is
|
|
percent gradient - this is better than nothing if you can't read the degree
|
|
scale (make it abundantly clear in the notes), but reading the wrong one
|
|
without realising gives useless results.</li>
|
|
|
|
<li>Pick survey points so you can get your head in, and so you can see both
|
|
ways as easily as possible. Note that Bolts are good things to use as
|
|
stations (because we can find them again), but don't put the compass within
|
|
30cm as it will give joke readings. Sight from the other end of the leg, or
|
|
put the compass behind it and look <em>past</em> the bolt.</li>
|
|
|
|
<li>Return instuments to the dessicator before you fall asleep
|
|
otherwise they are likely to fog up the next time. Don't leave them in the
|
|
cave, both for the above reason and because the next survey may need them
|
|
somewhere else entirely.</li>
|
|
|
|
<li>Leapfrogging is a good idea in general but you don't have to be religious
|
|
about it. It is almost impossible in tiny passage, and sometimes a point for
|
|
a survey station is so obvious that you <em>have</em> to use it, but can't
|
|
actually take readings <i>from</i> it.</li>
|
|
|
|
<li>Think ahead when surveying pitches, especially long ones. Take two tape
|
|
measures for stuff over 30m, or three well-organised people and some handy
|
|
big croc-clips!</li>
|
|
|
|
<li>Calibration is useful at 161a: ie. compass from lower to upper cairn, and
|
|
from lower cairn to Bräuning Zinken (if you know where it is - highest
|
|
point near right-hand edge of Bräuning Wall (just over the bush!)). See
|
|
the "<a href="../findit.htm">Taking bearings</a>" doc for photos. Clino
|
|
from lower to upper cairn and back down. Several readings for each
|
|
calibration is best.</li>
|
|
|
|
<li>Take care when holding your survey notes when using a carbide - they
|
|
catch fire very easily (a friend of mine lost over 300m of survey notes in
|
|
Mulu once like that - Andy F)</li>
|
|
</ul>
|
|
|
|
<p>that'll do for now – wook</p>
|
|
|
|
<hr />
|
|
|
|
|
|
</body>
|
|
</html>
|